SKTP-75 Page No. [1] [2] Current PageNo. 1

Features: LOW COST, HIGH RELIABILITY COMPACT SIZE, LIGHT WEIGHT 105℃ OUTPUT CAPACITOR. 100% FULL LOAD BURN-IN TEST INTERNATIONAL AC INPUT RANGE BUILT IN EMI FILTER, LOW RIPPLE NOISE HIGH EFFICIENCY, LOW WORKING TEMPERATURE BUILT IN PFC CIRCUIT SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE PROTECTED

SPECIFICATION MODEL SKTP-75A SKTP-75B SKTP-75C OUTPUT DC VOLTAGE 5V 12V -5V 5V 12V -12V 5V 15V -15V RATED CURRENT 7A 3A 0.6A 7A 3A 0.4A 6A 2.5A 0.5A CURRENT RANGE 1.5 ~ 10A 0.2 ~ 4A 0 ~ 0.6A 1.5 ~ 10A 0.2 ~ 4A 0 ~ 0.6A 1.5 ~ 10A 0.2 ~ 3A 0 ~ 0.6A RATED POWER 74W 75.8W 75W RIPPLE & NOISE (max.) Note.2 100mVp-p 120mVp-p 100mVp-p 100mVp-p 120mVp-p 120mVp-p 100mVp-p 120mVp-p 120mVp-p VOLTAGE TOLERANCE Note.3 ±3% ±3% ±8% ±3% ±4% ±8% ±3% ±4% ±8% LINE REGULATION ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% LOAD REGULATION ±3% ±4% ±8% ±3% ±4% ±8% ±3% ±4% ±8% SETUP, RISE, HOLD TIME 800ms, 60ms, 20ms. INPUT VOLTAGE RANGE 90~264VAC 47~63Hz 120~370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR PF>=0.95/230VAC, PF>=0.98/115VAC EFFICIENCY (Typ.) 70% AC CURRENT 1.5A/115V 0.8A/230V INRUSH CURRENT (max.) COLD START 40A/230VAC LEAKAGE CURRENT <2mA / 240VAC PROTECTION OVERLOAD 105 ~ 150% PULSE MODE RESET:AUTO RECOVERY OVER VOLTAGE 115 ~ 135% ON +5V TYPE:SHUTDOWN RESET:RE POWER ON ENVIRONMENT WORKING TEMP.,HUMIDITY -10 ~ +60℃ (REFER TO OUTPUT DERATING CURVE), 20%~90% RH STORAGE TEMP., HUMIDITY -20 ~ +85℃ , 10 ~ 95% RH TEMP. COEFFICIENT ±0.03% / ℃ (0 ~ 50℃) VIBRATION 1 0 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY & EMC (Note 4) SAFETY STANDARDS UL1950,TUV EN60950 APPROVED.   EMS STANDARDS CISPR22 (EN55022) CLASS B, EN61000-4-2,3,4,5,6,8,11; ENV50204, EN61000-3-2,-3 VERIFICATION   DIMENSION 179*99*33mm (L*W*H)   PACKING 550gs NOTE 1.ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25oC 70% RH. AMBIENT. 2.TOLERANCE GINCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION. 3.RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR. 4.LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD. 5.OUTPUT PROVIDE UP TO MAXIMUM CURRENT, BUT TATAL POWER CAN NOT EXCEED MAX. OUTPUT POWER. 6.MOUNTING HOLES M1 AND M2 SHOULD BE GROUNDED FOR EMI PURPOSES. 7.OUTPUT PROVIDE UP TO MAX. CURRENT, BUT TOTAL OUTPUT POWER CAN NOT EXCEED RATED OUTPUT POWER.